Important Info

Featured Sponsor

Become an Author

GeoPrac.net is a community site, we are only as good as the content our members contribute! Whether it's a one time contribution, or a monthly or quarterly article, please consider becoming an author!

Latest Comments in...

San Francisco Millennium Tower Has Settled 16 Inches
Misrepresents actual foundation geometry. Photos show deep excavation to ne
New FHWA Soil Nail Manual Addresses LRFD, Hollow Bars
Good evening from Barcelona, Spain. I am witting to you because of I am le
Engineering Geologists vs Geological Engineers vs Geotechnic
Geological engineer from Spain (looking for job smiley geoengineer.martin@gmail
A Whole Lotta Shakin' Goin' On: Center for Geotechnical Mode
Randy, While the UC Davis lab is impressive I believe the USACE Centrifuge
Content
Maine Bridge Uses First GRS Wall in a Marine Environment PDF Print E-mail
Articles - Retaining Walls
Written by Lindsey Manthei O'Connor   
Friday, 05 June 2015 06:31

THE CHALLENGE:

In 2013, the town of North Haven, Maine, began construction on a very unique bridge project. The goal was to re-build a deteriorating bridge that provided access to four seasonal homes and was an important wharf for the local lobster industry.

BEFORE: The old bridge needed replacing

BEFORE: The old bridge needed replacing

The town faced several challenges with this project:

  • North Haven is an island located on the coast of Maine; all construction materials and equipment needed to be transported to the island by boat.
  • The significant daily tidal fluctuations affected the daily construction duration. At high tide, most of the abutments are/were actually under water.
  • The town wanted to integrate an existing pier with the new bridge construction to minimize construction time and costs.
  • Construction needed to be completed during the winter and early spring to minimize the impact on residents and fishermen.
  • The wall had to withstand potential impact from the boats navigating the waterway.
Project Stats: Project Name: Maine DOT Beach Bridge
Owner: City of North Haven; Maine DOT
Block Manufacturer: Redi-Rock of Central Maine
Installer: Prock Marine Co.
Specifying Engineer: T.Y. Lin International
Wall Design: Jeffrey M. Benway, P.E., SFC Engineering Partnership, Inc
Project Location: North Haven, Maine
Year Built: 2013

THE SOLUTION:

The remote location of North Haven led the design team to search for a simpler solution than a typical pile driven foundation for the bridge abutments. The solution was a Geosynthetic Reinforced Soil - Integrated Bridge System (GRS-IBS), completed as a joint effort of the town of North Haven and the Maine Department of Transportation.

Redi-Rock-Limestone-GRS-retaining-wall-2.jpg

Using a GRS-IBS solution allowed installers to beat the construction schedule

“A GRS wall was by far the cheapest and easiest to incorporate in that type of environment,” explained Josh Olund, P.E. .of T.Y. Lin International. “This is the first time a GRS wall has been used in a marine or tidal environment. It’s also the first time being used in a 2 span bridge arrangement,” Olund said.

“The main difference between a GRS wall and a traditional mechanically stabilized earth abutment wall is that reinforcing fabric is used in much more closely spaced layers, and the fabric is not geogrid,” explained Jeff Benway, P.E. of SFC Engineering Partnership, Inc. “What’s typically used is more like a filter fabric. It doesn’t have the same strength as geogrid, but it’s much more closely spaced - every 6 to 9 inches (150 to 230 millimeters) versus every 18 inches (457 millimeters) with a traditional Redi-Rock wall. This allows the fabric to act as a tension element in the soil. The facing unit isn’t really retaining the soil at all; it’s simply preventing erosion of the reinforced soil mass.”

The existing bridge pier was reused to cut down on cost and time, which was important because the project needed to be completed during the winter and the spring. They were able to reuse the bridge pier by using lightweight concrete beams that were specified by the engineering team.

The Limestone textured Redi-Rock blocks matched the aesthetic look of the existing bridge pier, and fit in with the natural look of the environment.

“This is located in one of the most spectacular sailing harbors along the coast of Maine,” explained Joe Stone, North Haven administrator. “It was important that the natural scenic beauty of the site not be damaged by the bridge.”

Redi-Rock of Central Maine supplied the zero batter, Limestone texture Redi-Rock blocks. Since the bridge abutment is partially submerged in the ocean at high tide, the blocks were cast using a low permeability concrete mix that met all Maine DOT specs. These blocks were unique in that they required flat tops and bottoms with no shear knob or groove, which are a standard part of any Redi-Rock block.

This GRS-IBS solution is the first in a marine environment.

This GRS-IBS solution is the first in a marine environment.

This custom block design allowed the geosynthetic fabric to be sandwiched between the flat blocks. The design also included intermediate, non-attached layers of Tencate Mirafi HP 770PET fabric located at mid-height of the blocks (every 9 inches, or 230 millimeters).

A benefit of using wet cast precast modular blocks in a project like this is that the installation crew could compact the reinforced soil mass right up to the back of the blocks. The massive size of each Redi-Rock block allowed the facing structure to handle compaction of the soil directly behind it.

“This area doesn’t get wave action, but there’s a very large tidal change - around 6 to 8 feet (1.82 to 2.44 meters). They wanted to use a larger block system that could withstand the tidal changes as well as potential impact from boats,” Benway said.

Even though the tidal fluctuations posed a challenge to the installation, the crew was able to beat their original schedule, according to Olund. The overall duration for the project was about 4 months, which included everything from demolition through construction.

THE OUTCOME:

At the tallest point, the abutment walls stand 15 feet (4.57 meters) tall, with 4 feet (1.22 meters) buried. The project included 344 total Redi-Rock blocks, equaling 1,918 square feet (178.19 square meters).

“It’s been widely accepted by the property owners that abut it and the fishermen who use it,” Stone said. “People appreciate the fact that it’s more robust and safer than its predecessor and built to modern standards.”

The abutment also includes bumpers for boats that pull up to unload their catch. The walls were engineered to sustain potential boat impact.

The abutment also includes bumpers for boats that pull up to unload their catch. The walls were engineered to sustain potential boat impact.

ABOUT REDI-ROCK:

Redi-Rock is the leading retaining wall system for building tall gravity walls and even taller reinforced walls. With family business roots running all the way back to farming in the 1930s, Redi-Rock has built a solid reputation for proven solutions that will stand the test of time.  Find out more at Redi-Rock.com or contact Lindsey Manthei O’Connor at lindsey@redi-rock.com, or 866-222-8400 ext. 3032.

Hits: 4619
Trackback(0)
Comments (0)add comment

Write comment

security image
Write the displayed characters


busy
Last Updated on Friday, 05 June 2015 06:36
 

Article Copyright

All content in the ARTICLES section of GeoPrac.net is copyrighted by their authors unless otherwise noted and reproduced here with permission. Refer to the Copyright Information page or the Legal / Terms of Use page for more information.